Calculating Wattage for Resistor in High Frequency Application?Resistor wattage?Resistor wattage for HDMI hackTLC5940NT + 12v 5050 led stripImprove Rise Time on 1Hz SignalDetermining the surge duration of a double exponential transient?Resistor surge ratingZero Crossing Detection of ~ 400 kHz Signal with MCUpower supply remote sense protection resistor value?calculating maximum sense speed of amplified phototransistor circuitMay I use a smaller wattage resistor as mosfet's gate driver for a very short time?

On a tidally locked planet, would time be quantized?

What is Cash Advance APR?

Is it possible to have a strip of cold climate in the middle of a planet?

Is it improper etiquette to ask your opponent what his/her rating is before the game?

Does an advisor owe his/her student anything? Will an advisor keep a PhD student only out of pity?

Should I stop contributing to retirement accounts?

It grows, but water kills it

"Spoil" vs "Ruin"

The IT department bottlenecks progress. How should I handle this?

Delivering sarcasm

Why can Carol Danvers change her suit colours in the first place?

Removing files under particular conditions (number of files, file age)

250 Floor Tower

What is the evidence for the "tyranny of the majority problem" in a direct democracy context?

Is it better practice to read straight from sheet music rather than memorize it?

How can Trident be so inexpensive? Will it orbit Triton or just do a (slow) flyby?

Should I outline or discovery write my stories?

Problem with TransformedDistribution

Pre-mixing cryogenic fuels and using only one fuel tank

Drawing ramified coverings with tikz

Why Shazam when there is already Superman?

Redundant comparison & "if" before assignment

How to indicate a cut out for a product window

Offered money to buy a house, seller is asking for more to cover gap between their listing and mortgage owed



Calculating Wattage for Resistor in High Frequency Application?


Resistor wattage?Resistor wattage for HDMI hackTLC5940NT + 12v 5050 led stripImprove Rise Time on 1Hz SignalDetermining the surge duration of a double exponential transient?Resistor surge ratingZero Crossing Detection of ~ 400 kHz Signal with MCUpower supply remote sense protection resistor value?calculating maximum sense speed of amplified phototransistor circuitMay I use a smaller wattage resistor as mosfet's gate driver for a very short time?













1












$begingroup$


I am making a MOSFET driving circuit.

Frequency : 400 kHz [50% duty cycle]

Gate voltage: 12 V

Total gate charge : 210 nC as per datasheet IRFP460

Rise time: 100 ns

[Q=I*t]

Current: 2.1 A

Gate resistor: V/I > 12/2.1 > 5.7 ohm

Peak power: I * I * R > 2.1 * 2.1 * 5.7 > 25.1370 W

Average power: [Peak Power/Frequency]: 25.1370/400000 > 0.0000628425 [Ws]



1 watt resistor is OK ?










share|improve this question











$endgroup$











  • $begingroup$
    Dividing peak power by frequency doesn't make sense to me. As you say, the units are watt-seconds, not watts.
    $endgroup$
    – Elliot Alderson
    3 hours ago















1












$begingroup$


I am making a MOSFET driving circuit.

Frequency : 400 kHz [50% duty cycle]

Gate voltage: 12 V

Total gate charge : 210 nC as per datasheet IRFP460

Rise time: 100 ns

[Q=I*t]

Current: 2.1 A

Gate resistor: V/I > 12/2.1 > 5.7 ohm

Peak power: I * I * R > 2.1 * 2.1 * 5.7 > 25.1370 W

Average power: [Peak Power/Frequency]: 25.1370/400000 > 0.0000628425 [Ws]



1 watt resistor is OK ?










share|improve this question











$endgroup$











  • $begingroup$
    Dividing peak power by frequency doesn't make sense to me. As you say, the units are watt-seconds, not watts.
    $endgroup$
    – Elliot Alderson
    3 hours ago













1












1








1





$begingroup$


I am making a MOSFET driving circuit.

Frequency : 400 kHz [50% duty cycle]

Gate voltage: 12 V

Total gate charge : 210 nC as per datasheet IRFP460

Rise time: 100 ns

[Q=I*t]

Current: 2.1 A

Gate resistor: V/I > 12/2.1 > 5.7 ohm

Peak power: I * I * R > 2.1 * 2.1 * 5.7 > 25.1370 W

Average power: [Peak Power/Frequency]: 25.1370/400000 > 0.0000628425 [Ws]



1 watt resistor is OK ?










share|improve this question











$endgroup$




I am making a MOSFET driving circuit.

Frequency : 400 kHz [50% duty cycle]

Gate voltage: 12 V

Total gate charge : 210 nC as per datasheet IRFP460

Rise time: 100 ns

[Q=I*t]

Current: 2.1 A

Gate resistor: V/I > 12/2.1 > 5.7 ohm

Peak power: I * I * R > 2.1 * 2.1 * 5.7 > 25.1370 W

Average power: [Peak Power/Frequency]: 25.1370/400000 > 0.0000628425 [Ws]



1 watt resistor is OK ?







resistors high-frequency






share|improve this question















share|improve this question













share|improve this question




share|improve this question








edited 3 hours ago









Transistor

87.1k785189




87.1k785189










asked 3 hours ago









Israr SayedIsrar Sayed

204




204











  • $begingroup$
    Dividing peak power by frequency doesn't make sense to me. As you say, the units are watt-seconds, not watts.
    $endgroup$
    – Elliot Alderson
    3 hours ago
















  • $begingroup$
    Dividing peak power by frequency doesn't make sense to me. As you say, the units are watt-seconds, not watts.
    $endgroup$
    – Elliot Alderson
    3 hours ago















$begingroup$
Dividing peak power by frequency doesn't make sense to me. As you say, the units are watt-seconds, not watts.
$endgroup$
– Elliot Alderson
3 hours ago




$begingroup$
Dividing peak power by frequency doesn't make sense to me. As you say, the units are watt-seconds, not watts.
$endgroup$
– Elliot Alderson
3 hours ago










1 Answer
1






active

oldest

votes


















2












$begingroup$

Dividing the peak power by the frequency is not useful.



Instead, you would multiply it by the duty cycle. If you're dumping 25 W of power into the resistor for 2 × 100 ns out of every 2.5 µs. This would be an average power of



$$25 W cdotfrac2 cdot 100 ns2.5 mu s = 2 W$$



Clearly, your 1W resistor is not going to cut it!



However, the peak instantaneous power is not really a good estimate of the average power during the switching transient. A better estimate can be arrived at by considering the energy flow into and out of the gate capacitance.



For an R-C circuit, the energy dissipated in the resistor is basically equal to the energy that ends up on the capacitor. If your gate charge is 210 nC and your gate voltage is 12V, this represents



$$Energy = frac12cdot Charge cdot Voltage$$



$$0.5 cdot 210 nC cdot 12 V = 1.26 mu J$$



This is the energy you're dumping into the gate capacitance, and then dumping out again on every switching cycle. All of this energy gets dissipated in the gate resistor.



To get the average power, multiply the energy per cycle by the number of cycles per second, giving



$$1.26 mu J cdot 2 cdot 400 kHz = 1.088 W$$



Your 1W resistor would be running at its limit, with no margin. I would use a 2W resistor here.






share|improve this answer











$endgroup$












    Your Answer





    StackExchange.ifUsing("editor", function ()
    return StackExchange.using("mathjaxEditing", function ()
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
    );
    );
    , "mathjax-editing");

    StackExchange.ifUsing("editor", function ()
    return StackExchange.using("schematics", function ()
    StackExchange.schematics.init();
    );
    , "cicuitlab");

    StackExchange.ready(function()
    var channelOptions =
    tags: "".split(" "),
    id: "135"
    ;
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function()
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled)
    StackExchange.using("snippets", function()
    createEditor();
    );

    else
    createEditor();

    );

    function createEditor()
    StackExchange.prepareEditor(
    heartbeatType: 'answer',
    autoActivateHeartbeat: false,
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader:
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    ,
    onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    );



    );













    draft saved

    draft discarded


















    StackExchange.ready(
    function ()
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f428730%2fcalculating-wattage-for-resistor-in-high-frequency-application%23new-answer', 'question_page');

    );

    Post as a guest















    Required, but never shown

























    1 Answer
    1






    active

    oldest

    votes








    1 Answer
    1






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes









    2












    $begingroup$

    Dividing the peak power by the frequency is not useful.



    Instead, you would multiply it by the duty cycle. If you're dumping 25 W of power into the resistor for 2 × 100 ns out of every 2.5 µs. This would be an average power of



    $$25 W cdotfrac2 cdot 100 ns2.5 mu s = 2 W$$



    Clearly, your 1W resistor is not going to cut it!



    However, the peak instantaneous power is not really a good estimate of the average power during the switching transient. A better estimate can be arrived at by considering the energy flow into and out of the gate capacitance.



    For an R-C circuit, the energy dissipated in the resistor is basically equal to the energy that ends up on the capacitor. If your gate charge is 210 nC and your gate voltage is 12V, this represents



    $$Energy = frac12cdot Charge cdot Voltage$$



    $$0.5 cdot 210 nC cdot 12 V = 1.26 mu J$$



    This is the energy you're dumping into the gate capacitance, and then dumping out again on every switching cycle. All of this energy gets dissipated in the gate resistor.



    To get the average power, multiply the energy per cycle by the number of cycles per second, giving



    $$1.26 mu J cdot 2 cdot 400 kHz = 1.088 W$$



    Your 1W resistor would be running at its limit, with no margin. I would use a 2W resistor here.






    share|improve this answer











    $endgroup$

















      2












      $begingroup$

      Dividing the peak power by the frequency is not useful.



      Instead, you would multiply it by the duty cycle. If you're dumping 25 W of power into the resistor for 2 × 100 ns out of every 2.5 µs. This would be an average power of



      $$25 W cdotfrac2 cdot 100 ns2.5 mu s = 2 W$$



      Clearly, your 1W resistor is not going to cut it!



      However, the peak instantaneous power is not really a good estimate of the average power during the switching transient. A better estimate can be arrived at by considering the energy flow into and out of the gate capacitance.



      For an R-C circuit, the energy dissipated in the resistor is basically equal to the energy that ends up on the capacitor. If your gate charge is 210 nC and your gate voltage is 12V, this represents



      $$Energy = frac12cdot Charge cdot Voltage$$



      $$0.5 cdot 210 nC cdot 12 V = 1.26 mu J$$



      This is the energy you're dumping into the gate capacitance, and then dumping out again on every switching cycle. All of this energy gets dissipated in the gate resistor.



      To get the average power, multiply the energy per cycle by the number of cycles per second, giving



      $$1.26 mu J cdot 2 cdot 400 kHz = 1.088 W$$



      Your 1W resistor would be running at its limit, with no margin. I would use a 2W resistor here.






      share|improve this answer











      $endgroup$















        2












        2








        2





        $begingroup$

        Dividing the peak power by the frequency is not useful.



        Instead, you would multiply it by the duty cycle. If you're dumping 25 W of power into the resistor for 2 × 100 ns out of every 2.5 µs. This would be an average power of



        $$25 W cdotfrac2 cdot 100 ns2.5 mu s = 2 W$$



        Clearly, your 1W resistor is not going to cut it!



        However, the peak instantaneous power is not really a good estimate of the average power during the switching transient. A better estimate can be arrived at by considering the energy flow into and out of the gate capacitance.



        For an R-C circuit, the energy dissipated in the resistor is basically equal to the energy that ends up on the capacitor. If your gate charge is 210 nC and your gate voltage is 12V, this represents



        $$Energy = frac12cdot Charge cdot Voltage$$



        $$0.5 cdot 210 nC cdot 12 V = 1.26 mu J$$



        This is the energy you're dumping into the gate capacitance, and then dumping out again on every switching cycle. All of this energy gets dissipated in the gate resistor.



        To get the average power, multiply the energy per cycle by the number of cycles per second, giving



        $$1.26 mu J cdot 2 cdot 400 kHz = 1.088 W$$



        Your 1W resistor would be running at its limit, with no margin. I would use a 2W resistor here.






        share|improve this answer











        $endgroup$



        Dividing the peak power by the frequency is not useful.



        Instead, you would multiply it by the duty cycle. If you're dumping 25 W of power into the resistor for 2 × 100 ns out of every 2.5 µs. This would be an average power of



        $$25 W cdotfrac2 cdot 100 ns2.5 mu s = 2 W$$



        Clearly, your 1W resistor is not going to cut it!



        However, the peak instantaneous power is not really a good estimate of the average power during the switching transient. A better estimate can be arrived at by considering the energy flow into and out of the gate capacitance.



        For an R-C circuit, the energy dissipated in the resistor is basically equal to the energy that ends up on the capacitor. If your gate charge is 210 nC and your gate voltage is 12V, this represents



        $$Energy = frac12cdot Charge cdot Voltage$$



        $$0.5 cdot 210 nC cdot 12 V = 1.26 mu J$$



        This is the energy you're dumping into the gate capacitance, and then dumping out again on every switching cycle. All of this energy gets dissipated in the gate resistor.



        To get the average power, multiply the energy per cycle by the number of cycles per second, giving



        $$1.26 mu J cdot 2 cdot 400 kHz = 1.088 W$$



        Your 1W resistor would be running at its limit, with no margin. I would use a 2W resistor here.







        share|improve this answer














        share|improve this answer



        share|improve this answer








        edited 2 hours ago

























        answered 3 hours ago









        Dave TweedDave Tweed

        122k9152263




        122k9152263



























            draft saved

            draft discarded
















































            Thanks for contributing an answer to Electrical Engineering Stack Exchange!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid


            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.

            Use MathJax to format equations. MathJax reference.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function ()
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f428730%2fcalculating-wattage-for-resistor-in-high-frequency-application%23new-answer', 'question_page');

            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            Popular posts from this blog

            How should I use the fbox command correctly to avoid producing a Bad Box message?How to put a long piece of text in a box?How to specify height and width of fboxIs there an arrayrulecolor-like command to change the rule color of fbox?What is the command to highlight bad boxes in pdf?Why does fbox sometimes place the box *over* the graphic image?how to put the text in the boxHow to create command for a box where text inside the box can automatically adjust?how can I make an fbox like command with certain color, shape and width of border?how to use fbox in align modeFbox increase the spacing between the box and it content (inner margin)how to change the box height of an equationWhat is the use of the hbox in a newcommand command?

            Doxepinum Nexus interni Notae | Tabula navigationis3158DB01142WHOa682390"Structural Analysis of the Histamine H1 Receptor""Transdermal and Topical Drug Administration in the Treatment of Pain""Antidepressants as antipruritic agents: A review"

            inputenc: Unicode character … not set up for use with LaTeX The Next CEO of Stack OverflowEntering Unicode characters in LaTeXHow to solve the `Package inputenc Error: Unicode char not set up for use with LaTeX` problem?solve “Unicode char is not set up for use with LaTeX” without special handling of every new interesting UTF-8 characterPackage inputenc Error: Unicode character ² (U+B2)(inputenc) not set up for use with LaTeX. acroI2C[I²C]package inputenc error unicode char (u + 190) not set up for use with latexPackage inputenc Error: Unicode char u8:′ not set up for use with LaTeX. 3′inputenc Error: Unicode char u8: not set up for use with LaTeX with G-BriefPackage Inputenc Error: Unicode char u8: not set up for use with LaTeXPackage inputenc Error: Unicode char ́ (U+301)(inputenc) not set up for use with LaTeX. includePackage inputenc Error: Unicode char ̂ (U+302)(inputenc) not set up for use with LaTeX. … $widehatleft (OA,AA' right )$Package inputenc Error: Unicode char â„¡ (U+2121)(inputenc) not set up for use with LaTeX. printbibliography[heading=bibintoc]Package inputenc Error: Unicode char − (U+2212)(inputenc) not set up for use with LaTeXPackage inputenc Error: Unicode character α (U+3B1) not set up for use with LaTeXPackage inputenc Error: Unicode characterError: ! Package inputenc Error: Unicode char ⊘ (U+2298)(inputenc) not set up for use with LaTeX